![\"IMG_3021\"](\"http:\/\/westoahuroofing.com\/wp-content\/uploads\/2014\/09\/IMG_3021.jpg\")
<\/a><\/div>\n<\/a><\/div>\nReference Downloads:<\/h2>\n
Homeowner’s Handbook to Prepare for Natural Hazards<\/a><\/p>\n Roof Underlayment for Asphalt Shingle Roofs<\/a><\/p>\n Asphalt Shingle Roofing for High Wind Regions<\/a><\/p>\n Coastal Construction Manual – Ch. 11 – Designing the Building Envelope<\/a><\/p>\n 1.\u00a0 CertainTeed Landmark Solaris Gold – Resawn Shake<\/a><\/p>\n 2.\u00a0 CertainTeed WinterGuard<\/a><\/p>\n 3.\u00a0 CertainTeed Diamond Deck<\/a><\/p>\n 4.\u00a0 CertainTeed Solaris Hip & Ridge Caps<\/a><\/p>\n 5.\u00a0 CertainTeed SwiftStart Starters<\/a><\/p>\n 6.\u00a0 CertainTeed Ridge Vent<\/a><\/p>\n 7.\u00a0 Pipe Vent Flashings – Lead<\/p>\n 8.\u00a0 1.5″x1.5″ Painted Galvanized Drip Edge Flashing<\/p>\n 9.\u00a0 Henry Wet Patch 208R<\/a><\/p>\n 10.\u00a0 Hot Dipped Galvanized Nails<\/p>\n 1.\u00a0 Strip & remove of all existing roofing and dispose of in dump truck.\u00a0 Dump Truck to be removed at the end of work day.<\/p>\n 2.\u00a0 Inspect plywood, rafters, and fascia board for damage and replace with new.<\/p>\n 3.\u00a0 Install CertainTeed WinterGuard peel & stick underlayment throughout entire roof area.<\/p>\n 4.\u00a0 Install CertainTeed Diamond Deck Synthetic Underlayment throughout entire roof area fastened with 3\/8″ staples.<\/p>\n 5.\u00a0 Install 1.5″ x 1.5″ primed shingle drip edge on rakes and eaves of roof.<\/p>\n 6.\u00a0 Install CertainTeed SwiftStart Starter Courses on all rakes and eaves.<\/p>\n 7.\u00a0 Apply Dabs of Roofing Cement under all shingles installed on rakes and eaves.<\/p>\n 8.\u00a0 Install lead pipe vent flashings on all vent through roof penetration.<\/p>\n 9.\u00a0 Install 2′ x 2′ square of CertainTeed WinterGuard peel & Stick underlayment around all roof penetrations.<\/p>\n 10.\u00a0 Install CertainTeed WinterGuard peel & stick underlayment on valleys.\u00a0 Install valley shingles using weave method.<\/p>\n 11.\u00a0 Install CertainTeed Landmark Solaris Gold Shingles as per manufacturer’s specifications with 6 nails per shingle.<\/p>\n 12.\u00a0 Install CertainTeed Hip & Ridge Caps with dabs of roofing cement under all hip.<\/p>\n 13.\u00a0 “Drill 2- to 3-inch-diameter holes in the sheathing between each truss or rafter approximately 1.5 inches down from the ridge. The holes should be equally spaced and should remove no more than 1\/2 of the total amount of sheathing area between the rafters. For example, if the rafters are spaced 24 inches o.c. and 2-inch-diameter holes are drilled, they should be spaced at 6 inches o.c., which will allow about 12 square inches of vent area per linear foot when the holes are placed along either side of the ridge.” – Designing The Building Envelope, Volume II, pg. 11-50 – 11-51<\/p>\n 14.\u00a0 Install CertainTeed 9″ Filtered Ridge Vent as per manufacturer’s specifications.<\/p>\n 15.\u00a0 Apply roofing cement along entire length of CertainTeed 9″ Filtered Ridge Vent.<\/p>\nMaterials:<\/h2>\n
\u00a0Installation Methods<\/h2>\n
<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div> <\/a><\/div><\/p>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div> <\/a><\/div> <\/a><\/div><\/p>\n<\/a><\/div> <\/a><\/div><\/p>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n<\/a><\/div>\n